Reply To: RE: Problem sending out fax

› VitalPBX Community Support › General Discussion › Problem sending out fax › Reply To: RE: Problem sending out fax

    • November 18, 2019 at 3:20 pm
    pftech-pf
    Participant
    Up
    0
    Down

    Ok thanks! It gives some errors. I send you the log (phone number are modified for privacy reasons):

    nov 18 16:04:18.58: [ 8707]: SESSION BEGIN 000000163 012412345678
    nov 18 16:04:18.58: [ 8707]: HylaFAX ™ Version 7.0.1
    nov 18 16:04:18.58: [ 8707]: SEND FAX: JOB 38 DEST 012412345678 COMMID 000000163 DEVICE ‘/dev/ttyIAX2’ FROM ‘Administrator <paolo@xxxxxxxxx.com>’ USER root
    nov 18 16:04:18.58: [ 8707]: STATE CHANGE: RUNNING -> SENDING
    nov 18 16:04:18.58: [ 8707]: <– [12:AT+FCLASS=1r]
    nov 18 16:04:18.58: [ 8707]: –> [2:OK]
    nov 18 16:04:18.58: [ 8707]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
    nov 18 16:04:18.62: [ 8707]: DIAL 012412345678
    nov 18 16:04:18.62: [ 8707]: <– [15:ATDT012412345678r]
    nov 18 16:04:31.27: [ 8707]: –> [7:CONNECT]
    nov 18 16:04:36.62: [ 8707]: –> [2:10 03]
    nov 18 16:04:36.62: [ 8707]: –> [10:NO CARRIER]
    nov 18 16:04:36.62: [ 8707]: MODEM No carrier
    nov 18 16:04:36.62: [ 8707]: <– [10:AT+FRS=21r]
    nov 18 16:04:36.62: [ 8707]: –> [5:ERROR]
    nov 18 16:04:36.62: [ 8707]: MODEM Command error
    nov 18 16:04:36.62: [ 8707]: Failure to receive silence (synchronization failure). {E100}
    nov 18 16:04:36.62: [ 8707]: <– [9:AT+FRS=7r]
    nov 18 16:04:36.62: [ 8707]: –> [5:ERROR]
    nov 18 16:04:36.62: [ 8707]: MODEM Command error
    nov 18 16:04:36.62: [ 8707]: Failure to receive silence (synchronization failure). {E100}
    nov 18 16:04:36.62: [ 8707]: <– [9:AT+FRH=3r]
    nov 18 16:04:36.62: [ 8707]: –> [5:ERROR]
    nov 18 16:04:36.62: [ 8707]: MODEM Command error
    nov 18 16:04:36.62: [ 8707]: SEND FAILED: JOB 38 DEST 012412345678 ERR Failure to receive silence (synchronization failure). {E100}
    nov 18 16:04:36.62: [ 8707]: <– [9:AT+FRS=7r]
    nov 18 16:04:36.62: [ 8707]: –> [5:ERROR]
    nov 18 16:04:36.62: [ 8707]: MODEM Command error
    nov 18 16:04:36.62: [ 8707]: Failure to receive silence (synchronization failure). {E100}
    nov 18 16:04:36.62: [ 8707]: <– [9:AT+FTH=3r]
    nov 18 16:04:36.62: [ 8707]: –> [5:ERROR]
    nov 18 16:04:36.62: [ 8707]: MODEM input buffering enabled
    nov 18 16:04:37.62: [ 8707]: <– [5:ATH0r]
    nov 18 16:04:37.62: [ 8707]: –> [2:OK]
    nov 18 16:04:37.62: [ 8707]: MODEM set DTR OFF
    nov 18 16:04:37.62: [ 8707]: MODEM set baud rate: 0 baud (flow control unchanged)
    nov 18 16:04:37.62: [ 8707]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
    nov 18 16:04:37.62: [ 8707]: SESSION END

    Can you help me? I really don’t know Hylafax hot it works!

    Regards,

    Paolo

    0