Settings – Telephony – Hardware

VitalPBX Community Support General Discussion Settings – Telephony – Hardware

  • Post
    LabSoft
    Participant

    the Detect hardware cannot find my card..

    Card ISDN BRI OpenVox b100e

    i try

    yum update … but nothing

    0
Viewing 9 replies - 1 through 9 (of 9 total)
  • Replies
    Rodrigo Cuadra
    Keymaster
    NI
    Up
    0
    Down

    You tried to detect the hardware from the interface?

    that comes out when you execute the command from ssh:
    # dahdi_hardware

    0
    LabSoft
    Participant
    Up
    0
    Down

    [root@vitalpbx ~]# dahdi_hardware
    pci:0000:02:00.0 zaphfc- 1397:2bd0 HFC-S ISDN BRI card

     

     

    0
    LabSoft
    Participant
    Up
    0
    Down

    in External – Trunks – Telephony

    DAHDi Trunk Parameters ? (nothing)

    0
    Up
    0
    Down

    may you post the input of dahdi_scan command

    0
    LabSoft
    Participant
    Up
    0
    Down

    i try this (i found in manual of card)

    wget http://downloads.asterisk.org/pub/telephony/libpri/releases/libpri-1.4.11.5.tar.gz

    tar -zxvf libpri-1.4.11.5.tar.gz

    wget http://downloads.openvox.cn/pub/drivers/dahdi-linux-complete/openvox_dahdi-linux-complete-current.tar.gz

    tar -xvzf openvox_dahdi-linux-complete-current.tar.gz

    wget http://downloads.asterisk.org/pub/telephony/asterisk/releases/asterisk-1.8.4.4.tar.gz

    tar -zxvf asterisk-1.8.4.4.tar.gz

     

    lspci –vvvv

     

    yum install bison

    yum install bison-devel

    yum install ncurses

    yum install ncurses-devel

    yum install zlib

    yum install zlib-devel

    yum install openssl

    yum install openssl-devel

    yum install gnutls-devel

    yum install gcc

    yum install gcc-c++

    yum install libxml2

    yum install libxml2-devel

    yum install libxml2-devel

     

    yum install kernel-devel-`uname –r`

    yum install kernel kernel-devel

    cd /usr/src/dahdi-linux-complete-2.11.1+2.11.1

     

    make

    make install

    make config

    modprobe dahdi

    modprobe zaphfc

    dahdi_genconf

    dahdi_cfg -vvv

    ————————————————————————————-

    after all this i found in hardware but can’t see on trunks
    —————————————————————————————-

    [root@vitalpbx ~]# dahdi_scan
    [1]
    active=yes
    alarms=OK
    description=HFC-S PCI A ISDN card 0 [TE]
    name=ZTHFC1
    manufacturer=Cologne Chips
    devicetype=HFC-S PCI-A ISDN
    location=PCI Bus 02 Slot 01
    basechan=1
    totchans=3
    irq=0
    type=digital-TE
    syncsrc=0
    lbo=0 db (CSU)/0-133 feet (DSX-1)
    coding_opts=AMI
    framing_opts=CCS
    coding=AMI
    framing=CCS
    [root@vitalpbx ~]#

     

     

    0
    Up
    0
    Down

    Did you try detect hardware from GUI (Dahdi >> Telephony >> Interfaces)

     

     

    0
    LabSoft
    Participant
    Up
    0
    Down

    I do Clear Install from begin… so.. we see.

    0
    Gary
    Participant
    Up
    0
    Down

    Not sure if it’s related but I can not setup Astribank.

     

    [root@vitalpbx ~]#
    [root@vitalpbx ~]# lsusb
    Bus 002 Device 006: ID e4e4:1161 Xorcom Ltd. Astribank 2 series
    Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    [root@vitalpbx ~]#
    [root@vitalpbx ~]# systemctl status dahdi
    ● dahdi.service – LSB: DAHDI kernel modules
    Loaded: loaded (/etc/rc.d/init.d/dahdi; bad; vendor preset: disabled)
    Active: failed (Result: exit-code) since Tue 2018-01-23 13:13:02 EST; 13min ago
    Docs: man:systemd-sysv-generator(8)
    Process: 4742 ExecStart=/etc/rc.d/init.d/dahdi start (code=exited, status=1/FAILURE)

    Jan 23 13:11:05 vitalpbx.local dahdi[4742]: xpp_usb: [ OK ]
    Jan 23 13:11:05 vitalpbx.local dahdi[4742]: Astribanks initialization is starting
    Jan 23 13:13:02 vitalpbx.local dahdi[4742]: Astribanks detection ………………………………………………………………………………….TIMEOUT
    Jan 23 13:13:02 vitalpbx.local dahdi[4742]: using ‘/etc/dahdi/assigned-spans.conf’
    Jan 23 13:13:02 vitalpbx.local dahdi[4742]: Running dahdi_cfg: DAHDI_SPANCONFIG failed on span 1: No such device or address (6)
    Jan 23 13:13:02 vitalpbx.local dahdi[4742]: [FAILED]
    Jan 23 13:13:02 vitalpbx.local systemd[1]: dahdi.service: control process exited, code=exited status=1
    Jan 23 13:13:02 vitalpbx.local systemd[1]: Failed to start LSB: DAHDI kernel modules.
    Jan 23 13:13:02 vitalpbx.local systemd[1]: Unit dahdi.service entered failed state.
    Jan 23 13:13:02 vitalpbx.local systemd[1]: dahdi.service failed.
    Hint: Some lines were ellipsized, use -l to show in full.
    [root@vitalpbx ~]#

     

    0
    Gary
    Participant
    Up
    0
    Down

    I resolved my issue by reinstalling VitalPBX and all is working.

    0
Viewing 9 replies - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.